1 So you had your oil changed or changed it yourself on you GM vehicle and the little light on the dashboard still says "Change Oil Soon". Your owner's manual should tell you how to reset it, however it's hidden away in one chapter or another.Here are the two easiest ways for most GMs.
Step 2 First you need to turn your car On. This is not starting the car! Turn the key two "clicks" forward. All the dashboard lights should come on, along with the radio and odometer.
Step 3 If your GM has the four buttons on the dashboard with all sorts of information:One button should have a road or "i" on it. Pushing this button will show your mileage, tire pressure, operating temperature, and all sorts of other stuff. You are looking for "oil life ##%". Once you find this, press and hold the button with the checkmark on it. After 5-10 seconds it should flash "oil life reset". Tada!
Step 4 If your vehicle does not have the buttons mentioned above:Turn the car "On" (without starting car!!)Press the gas pedal all the way to the floor 3 times within 5 seconds. This is trickier than it sounds. It must be pressed ALL the way to the floor ALL 3 times. Then wait 5-10 seconds. The Change Oil Soon light should blink then go out. If not, turn the car off and go through the steps again.
Saturday, June 6, 2009
How to Reset Change Oil Light on GMs, Chevrolet
1 So you had your oil changed or changed it yourself on you GM vehicle and the little light on the dashboard still says "Change Oil Soon". Your owner's manual should tell you how to reset it, however it's hidden away in one chapter or another.Here are the two easiest ways for most GMs.
Step 2 First you need to turn your car On. This is not starting the car! Turn the key two "clicks" forward. All the dashboard lights should come on, along with the radio and odometer.
Step 3 If your GM has the four buttons on the dashboard with all sorts of information:One button should have a road or "i" on it. Pushing this button will show your mileage, tire pressure, operating temperature, and all sorts of other stuff. You are looking for "oil life ##%". Once you find this, press and hold the button with the checkmark on it. After 5-10 seconds it should flash "oil life reset". Tada!
Step 4 If your vehicle does not have the buttons mentioned above:Turn the car "On" (without starting car!!)Press the gas pedal all the way to the floor 3 times within 5 seconds. This is trickier than it sounds. It must be pressed ALL the way to the floor ALL 3 times. Then wait 5-10 seconds. The Change Oil Soon light should blink then go out. If not, turn the car off and go through the steps again.
Step 2 First you need to turn your car On. This is not starting the car! Turn the key two "clicks" forward. All the dashboard lights should come on, along with the radio and odometer.
Step 3 If your GM has the four buttons on the dashboard with all sorts of information:One button should have a road or "i" on it. Pushing this button will show your mileage, tire pressure, operating temperature, and all sorts of other stuff. You are looking for "oil life ##%". Once you find this, press and hold the button with the checkmark on it. After 5-10 seconds it should flash "oil life reset". Tada!
Step 4 If your vehicle does not have the buttons mentioned above:Turn the car "On" (without starting car!!)Press the gas pedal all the way to the floor 3 times within 5 seconds. This is trickier than it sounds. It must be pressed ALL the way to the floor ALL 3 times. Then wait 5-10 seconds. The Change Oil Soon light should blink then go out. If not, turn the car off and go through the steps again.
How to RESET the Change Oil Light on a 1998 - 2001 Chevrolet Camaro
1 Frist, turn the ignition on.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
How to RESET the Change Oil Light on a 1998 - 2001 Chevrolet Camaro
1 Frist, turn the ignition on.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
How to RESET the Change Oil Light on a 1998 - 2001 Chevrolet Camaro
1 Frist, turn the ignition on.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
How to RESET the Change Oil Light on a 1998 - 2001 Chevrolet Camaro
1 Frist, turn the ignition on.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
How to RESET the Change Oil Light on a 1998 - 2001 Chevrolet Camaro
1 Frist, turn the ignition on.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
How to RESET the Change Oil Light on a 1998 - 2001 Chevrolet Camaro
1 Frist, turn the ignition on.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
Step 2 On the instrument panel, find the TRIP/OIL RESET button.
Step 3 Press and hold the button for 12 seconds.
Step 4 When the light flashes a couple of times and then goes out, then the system is reset.
How to Reset the Change Oil Light 1999, 2000, 2001 Suburban Yukon
1 Turn the ignition key to the RUN position but do not start the engine.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
How to Reset the Change Oil Light 1999, 2000, 2001 Suburban Yukon
1 Turn the ignition key to the RUN position but do not start the engine.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
How to Reset the Change Oil Light 1999, 2000, 2001 Suburban Yukon
1 Turn the ignition key to the RUN position but do not start the engine.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
How to Reset the Change Oil Light 1999, 2000, 2001 Suburban Yukon
1 Turn the ignition key to the RUN position but do not start the engine.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
How to Reset the Change Oil Light 1999, 2000, 2001 Suburban Yukon
1 Turn the ignition key to the RUN position but do not start the engine.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
How to Reset the Change Oil Light 1999, 2000, 2001 Suburban Yukon
1 Turn the ignition key to the RUN position but do not start the engine.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
2 Fully push and release the accelerator pedal three times within five seconds.
3 If the CHANGE OIL SOON light flashes 2 times, the system is reset. If the light comes on and stays on for 5 seconds, the system did not reset. You may have to repeat the procedure a couple of times if the system does not reset.
Friday, June 5, 2009
How To Reset Oil Change Light Acura Integra, 1994-01
To reset “MAINT REQD” light, press
the reset switch (A) located to the right of the steering column under the dash.
the reset switch (A) located to the right of the steering column under the dash.
How To Reset Oil Change Light Acura Integra, 1994-01
To reset “MAINT REQD” light, press
the reset switch (A) located to the right of the steering column under the dash.
the reset switch (A) located to the right of the steering column under the dash.
How To Reset Oil Change Light Acura Integra, 1994-01
To reset “MAINT REQD” light, press
the reset switch (A) located to the right of the steering column under the dash.
the reset switch (A) located to the right of the steering column under the dash.
How To Reset Oil Change Light Acura Integra, 1994-01
To reset “MAINT REQD” light, press
the reset switch (A) located to the right of the steering column under the dash.
the reset switch (A) located to the right of the steering column under the dash.
How To Reset Oil Change Light Acura Integra, 1994-01
To reset “MAINT REQD” light, press
the reset switch (A) located to the right of the steering column under the dash.
the reset switch (A) located to the right of the steering column under the dash.
How To Reset Oil Change Light Acura Integra, 1994-01
To reset “MAINT REQD” light, press
the reset switch (A) located to the right of the steering column under the dash.
the reset switch (A) located to the right of the steering column under the dash.
How To Reset Oil Change Light Acura, 2.2CL, 2.3CL, 2.5TL, 3.OCL, 1995-00; 3.2TL, 1995-98
To reset MAINTENANCE REQUIRED light, insert the ignition key into the slot to the left of the light on instrument panel.
How To Reset Oil Change Light Acura, 2.2CL, 2.3CL, 2.5TL, 3.OCL, 1995-00; 3.2TL, 1995-98
To reset MAINTENANCE REQUIRED light, insert the ignition key into the slot to the left of the light on instrument panel.
How To Reset Oil Change Light Acura, 2.2CL, 2.3CL, 2.5TL, 3.OCL, 1995-00; 3.2TL, 1995-98
To reset MAINTENANCE REQUIRED light, insert the ignition key into the slot to the left of the light on instrument panel.
How To Reset Oil Change Light Acura, 2.2CL, 2.3CL, 2.5TL, 3.OCL, 1995-00; 3.2TL, 1995-98
To reset MAINTENANCE REQUIRED light, insert the ignition key into the slot to the left of the light on instrument panel.
How To Reset Oil Change Light Acura, 2.2CL, 2.3CL, 2.5TL, 3.OCL, 1995-00; 3.2TL, 1995-98
To reset MAINTENANCE REQUIRED light, insert the ignition key into the slot to the left of the light on instrument panel.
How To Reset Oil Change Light Acura, 2.2CL, 2.3CL, 2.5TL, 3.OCL, 1995-00; 3.2TL, 1995-98
To reset MAINTENANCE REQUIRED light, insert the ignition key into the slot to the left of the light on instrument panel.
How To Reset Oil Change Light Acura
3.5RL, 1996-04 3.2L, 3.2TL, MDX, 1999-06
To reset MAINTENANCE REQUIRED light, turn ignition off, press and hold the SELECT and RESET buttons. Turn ignition on and hold buttons for 10 seconds until indicator resets.
How To Reset Oil Change Light Acura
3.5RL, 1996-04 3.2L, 3.2TL, MDX, 1999-06
To reset MAINTENANCE REQUIRED light, turn ignition off, press and hold the SELECT and RESET buttons. Turn ignition on and hold buttons for 10 seconds until indicator resets.
How To Reset Oil Change Light Acura
3.5RL, 1996-04 3.2L, 3.2TL, MDX, 1999-06
To reset MAINTENANCE REQUIRED light, turn ignition off, press and hold the SELECT and RESET buttons. Turn ignition on and hold buttons for 10 seconds until indicator resets.
How To Reset Oil Change Light Acura
3.5RL, 1996-04 3.2L, 3.2TL, MDX, 1999-06
To reset MAINTENANCE REQUIRED light, turn ignition off, press and hold the SELECT and RESET buttons. Turn ignition on and hold buttons for 10 seconds until indicator resets.
How To Reset Oil Change Light Acura
3.5RL, 1996-04 3.2L, 3.2TL, MDX, 1999-06
To reset MAINTENANCE REQUIRED light, turn ignition off, press and hold the SELECT and RESET buttons. Turn ignition on and hold buttons for 10 seconds until indicator resets.
How To Reset Oil Change Light Acura
3.5RL, 1996-04 3.2L, 3.2TL, MDX, 1999-06
To reset MAINTENANCE REQUIRED light, turn ignition off, press and hold the SELECT and RESET buttons. Turn ignition on and hold buttons for 10 seconds until indicator resets.
How To Reset Oil Change Light GMC Denali, Envoy, Sierra, Yukon, Chevrolet Suburban, Silverado 2006
To reset the CHANGE ENGINE OIL message, turn the ignition key to RUN with engine OFF. Fully press and release the accelerator pedal slowly three times with in five seconds. If the OIL LIFE RESET message flashes for 10 seconds, the system is resetting. Turn the key to LOCK.
How To Reset Oil Change Light GMC Denali, Envoy, Sierra, Yukon, Chevrolet Suburban, Silverado 2006
To reset the CHANGE ENGINE OIL message, turn the ignition key to RUN with engine OFF. Fully press and release the accelerator pedal slowly three times with in five seconds. If the OIL LIFE RESET message flashes for 10 seconds, the system is resetting. Turn the key to LOCK.
How To Reset Oil Change Light GMC Denali, Envoy, Sierra, Yukon, Chevrolet Suburban, Silverado 2006
To reset the CHANGE ENGINE OIL message, turn the ignition key to RUN with engine OFF. Fully press and release the accelerator pedal slowly three times with in five seconds. If the OIL LIFE RESET message flashes for 10 seconds, the system is resetting. Turn the key to LOCK.
How To Reset Oil Change Light GMC Denali, Envoy, Sierra, Yukon, Chevrolet Suburban, Silverado 2006
To reset the CHANGE ENGINE OIL message, turn the ignition key to RUN with engine OFF. Fully press and release the accelerator pedal slowly three times with in five seconds. If the OIL LIFE RESET message flashes for 10 seconds, the system is resetting. Turn the key to LOCK.
How To Reset Oil Change Light GMC Denali, Envoy, Sierra, Yukon, Chevrolet Suburban, Silverado 2006
To reset the CHANGE ENGINE OIL message, turn the ignition key to RUN with engine OFF. Fully press and release the accelerator pedal slowly three times with in five seconds. If the OIL LIFE RESET message flashes for 10 seconds, the system is resetting. Turn the key to LOCK.
How To Reset Oil Change Light GMC Denali, Envoy, Sierra, Yukon, Chevrolet Suburban, Silverado 2006
To reset the CHANGE ENGINE OIL message, turn the ignition key to RUN with engine OFF. Fully press and release the accelerator pedal slowly three times with in five seconds. If the OIL LIFE RESET message flashes for 10 seconds, the system is resetting. Turn the key to LOCK.
How To Reset Oil Change Light Chevrolet Corvette 2006
To reset the CHANGE ENGINE OIL message after an oil change. Press the TRIP button so the OIL LIFE percentage is displayed. Press RESET and hold for two seconds. OIL LIFE REMAINING 100% will appear. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
How To Reset Oil Change Light Chevrolet Corvette 2006
To reset the CHANGE ENGINE OIL message after an oil change. Press the TRIP button so the OIL LIFE percentage is displayed. Press RESET and hold for two seconds. OIL LIFE REMAINING 100% will appear. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
How To Reset Oil Change Light Chevrolet Corvette 2006
To reset the CHANGE ENGINE OIL message after an oil change. Press the TRIP button so the OIL LIFE percentage is displayed. Press RESET and hold for two seconds. OIL LIFE REMAINING 100% will appear. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
How To Reset Oil Change Light Chevrolet Corvette 2006
To reset the CHANGE ENGINE OIL message after an oil change. Press the TRIP button so the OIL LIFE percentage is displayed. Press RESET and hold for two seconds. OIL LIFE REMAINING 100% will appear. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
How To Reset Oil Change Light Chevrolet Corvette 2006
To reset the CHANGE ENGINE OIL message after an oil change. Press the TRIP button so the OIL LIFE percentage is displayed. Press RESET and hold for two seconds. OIL LIFE REMAINING 100% will appear. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
How To Reset Oil Change Light Chevrolet Corvette 2006
To reset the CHANGE ENGINE OIL message after an oil change. Press the TRIP button so the OIL LIFE percentage is displayed. Press RESET and hold for two seconds. OIL LIFE REMAINING 100% will appear. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Suburban/GMC Yukon XL, 2000-05 Chevrolet GMC Trucks Silverado, Sierra, 1999-05 Chevrolet Venture 2000
Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.
How To Reset Oil Change Light Chevrolet Corvette, 1997-05
Turn the ignition to ON. Press the TRIP button on the Driver Information Center (DIG) switch to view various menu choices and stop on OIL LIFE REMAINING. A message will display the percentage of oil life remaining. Press and hold the RESET button on the DIG switch for at least 2 seconds. A message will display the percentage of oil life remaining as 99 percent. The engine oil life monitor is now reset. Turn the ignition OFF.
How To Reset Oil Change Light Chevrolet Corvette, 1997-05
Turn the ignition to ON. Press the TRIP button on the Driver Information Center (DIG) switch to view various menu choices and stop on OIL LIFE REMAINING. A message will display the percentage of oil life remaining. Press and hold the RESET button on the DIG switch for at least 2 seconds. A message will display the percentage of oil life remaining as 99 percent. The engine oil life monitor is now reset. Turn the ignition OFF.
How To Reset Oil Change Light Chevrolet Corvette, 1997-05
Turn the ignition to ON. Press the TRIP button on the Driver Information Center (DIG) switch to view various menu choices and stop on OIL LIFE REMAINING. A message will display the percentage of oil life remaining. Press and hold the RESET button on the DIG switch for at least 2 seconds. A message will display the percentage of oil life remaining as 99 percent. The engine oil life monitor is now reset. Turn the ignition OFF.
How To Reset Oil Change Light Chevrolet Corvette, 1997-05
Turn the ignition to ON. Press the TRIP button on the Driver Information Center (DIG) switch to view various menu choices and stop on OIL LIFE REMAINING. A message will display the percentage of oil life remaining. Press and hold the RESET button on the DIG switch for at least 2 seconds. A message will display the percentage of oil life remaining as 99 percent. The engine oil life monitor is now reset. Turn the ignition OFF.
How To Reset Oil Change Light Chevrolet Corvette, 1997-05
Turn the ignition to ON. Press the TRIP button on the Driver Information Center (DIG) switch to view various menu choices and stop on OIL LIFE REMAINING. A message will display the percentage of oil life remaining. Press and hold the RESET button on the DIG switch for at least 2 seconds. A message will display the percentage of oil life remaining as 99 percent. The engine oil life monitor is now reset. Turn the ignition OFF.
How To Reset Oil Change Light Chevrolet Corvette, 1997-05
Turn the ignition to ON. Press the TRIP button on the Driver Information Center (DIG) switch to view various menu choices and stop on OIL LIFE REMAINING. A message will display the percentage of oil life remaining. Press and hold the RESET button on the DIG switch for at least 2 seconds. A message will display the percentage of oil life remaining as 99 percent. The engine oil life monitor is now reset. Turn the ignition OFF.
How To Reset Oil Change Light Chevrolet Corvette, 1990-96
After an oil change or when “CHANGE OIL” appears on Trip Monitor, with the ignition on and engine off, press ENG MET (A) button (located on Trip Monitor) once. Press ENG MET (A) button again within 5 seconds. Within 5 seconds, press and hold RANGE (B) button (1990-94) or GAUGES button (1995). The light will flash. When it stops flashing and goes out, the system is reset. If this does not occur within 10 seconds, repeat the procedure.
How To Reset Oil Change Light Chevrolet Corvette, 1990-96
After an oil change or when “CHANGE OIL” appears on Trip Monitor, with the ignition on and engine off, press ENG MET (A) button (located on Trip Monitor) once. Press ENG MET (A) button again within 5 seconds. Within 5 seconds, press and hold RANGE (B) button (1990-94) or GAUGES button (1995). The light will flash. When it stops flashing and goes out, the system is reset. If this does not occur within 10 seconds, repeat the procedure.
How To Reset Oil Change Light Chevrolet Corvette, 1990-96
After an oil change or when “CHANGE OIL” appears on Trip Monitor, with the ignition on and engine off, press ENG MET (A) button (located on Trip Monitor) once. Press ENG MET (A) button again within 5 seconds. Within 5 seconds, press and hold RANGE (B) button (1990-94) or GAUGES button (1995). The light will flash. When it stops flashing and goes out, the system is reset. If this does not occur within 10 seconds, repeat the procedure.
How To Reset Oil Change Light Chevrolet Corvette, 1990-96
After an oil change or when “CHANGE OIL” appears on Trip Monitor, with the ignition on and engine off, press ENG MET (A) button (located on Trip Monitor) once. Press ENG MET (A) button again within 5 seconds. Within 5 seconds, press and hold RANGE (B) button (1990-94) or GAUGES button (1995). The light will flash. When it stops flashing and goes out, the system is reset. If this does not occur within 10 seconds, repeat the procedure.
How To Reset Oil Change Light Chevrolet Corvette, 1990-96
After an oil change or when “CHANGE OIL” appears on Trip Monitor, with the ignition on and engine off, press ENG MET (A) button (located on Trip Monitor) once. Press ENG MET (A) button again within 5 seconds. Within 5 seconds, press and hold RANGE (B) button (1990-94) or GAUGES button (1995). The light will flash. When it stops flashing and goes out, the system is reset. If this does not occur within 10 seconds, repeat the procedure.
How To Reset Oil Change Light Chevrolet Corvette, 1990-96
After an oil change or when “CHANGE OIL” appears on Trip Monitor, with the ignition on and engine off, press ENG MET (A) button (located on Trip Monitor) once. Press ENG MET (A) button again within 5 seconds. Within 5 seconds, press and hold RANGE (B) button (1990-94) or GAUGES button (1995). The light will flash. When it stops flashing and goes out, the system is reset. If this does not occur within 10 seconds, repeat the procedure.
How To Reset Oil Change Light Chevrolet Malibu, Malibu Maxx 2004-06; 2006 HHR, Cobalt, Pontiac G6, Solstice
Turn ignition to run engine off. Display OIL LIFE RESET in the Driver Information Center (DIC). Press and hold the ENTER button for at least one second. An ACKNOWLEDGED’ display message will appear for three second or until the next button is pressed. This will tell you the system has been reset. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Malibu, Malibu Maxx 2004-06; 2006 HHR, Cobalt, Pontiac G6, Solstice
Turn ignition to run engine off. Display OIL LIFE RESET in the Driver Information Center (DIC). Press and hold the ENTER button for at least one second. An ACKNOWLEDGED’ display message will appear for three second or until the next button is pressed. This will tell you the system has been reset. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Malibu, Malibu Maxx 2004-06; 2006 HHR, Cobalt, Pontiac G6, Solstice
Turn ignition to run engine off. Display OIL LIFE RESET in the Driver Information Center (DIC). Press and hold the ENTER button for at least one second. An ACKNOWLEDGED’ display message will appear for three second or until the next button is pressed. This will tell you the system has been reset. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Malibu, Malibu Maxx 2004-06; 2006 HHR, Cobalt, Pontiac G6, Solstice
Turn ignition to run engine off. Display OIL LIFE RESET in the Driver Information Center (DIC). Press and hold the ENTER button for at least one second. An ACKNOWLEDGED’ display message will appear for three second or until the next button is pressed. This will tell you the system has been reset. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Malibu, Malibu Maxx 2004-06; 2006 HHR, Cobalt, Pontiac G6, Solstice
Turn ignition to run engine off. Display OIL LIFE RESET in the Driver Information Center (DIC). Press and hold the ENTER button for at least one second. An ACKNOWLEDGED’ display message will appear for three second or until the next button is pressed. This will tell you the system has been reset. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Malibu, Malibu Maxx 2004-06; 2006 HHR, Cobalt, Pontiac G6, Solstice
Turn ignition to run engine off. Display OIL LIFE RESET in the Driver Information Center (DIC). Press and hold the ENTER button for at least one second. An ACKNOWLEDGED’ display message will appear for three second or until the next button is pressed. This will tell you the system has been reset. Turn the key to OFF. If the “CHANGE ENGINE OIL” message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet SSR, Impala, Monte Carlo, 2006
Press the fuel information button until ENGINE OIL LIFE appears on the Driver Information Center (DIC). Press and hold the select button. The engine oil life percentage will return to 100. Turn the key to OFF. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet SSR, Impala, Monte Carlo, 2006
Press the fuel information button until ENGINE OIL LIFE appears on the Driver Information Center (DIC). Press and hold the select button. The engine oil life percentage will return to 100. Turn the key to OFF. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet SSR, Impala, Monte Carlo, 2006
Press the fuel information button until ENGINE OIL LIFE appears on the Driver Information Center (DIC). Press and hold the select button. The engine oil life percentage will return to 100. Turn the key to OFF. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet SSR, Impala, Monte Carlo, 2006
Press the fuel information button until ENGINE OIL LIFE appears on the Driver Information Center (DIC). Press and hold the select button. The engine oil life percentage will return to 100. Turn the key to OFF. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet SSR, Impala, Monte Carlo, 2006
Press the fuel information button until ENGINE OIL LIFE appears on the Driver Information Center (DIC). Press and hold the select button. The engine oil life percentage will return to 100. Turn the key to OFF. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet SSR, Impala, Monte Carlo, 2006
Press the fuel information button until ENGINE OIL LIFE appears on the Driver Information Center (DIC). Press and hold the select button. The engine oil life percentage will return to 100. Turn the key to OFF. If the CHANGE ENGINE OIL message comes back on when you start your vehicle, the engine oil life system has not reset. Repeat the procedure.
How To Reset Oil Change Light Chevrolet Impala, Monte Carlo, 2000-05
Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHG OIL SOON light flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio®. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to verify the exit.
How To Reset Oil Change Light Chevrolet Impala, Monte Carlo, 2000-05
Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHG OIL SOON light flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio®. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to verify the exit.
How To Reset Oil Change Light Chevrolet Impala, Monte Carlo, 2000-05
Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHG OIL SOON light flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio®. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to verify the exit.
How To Reset Oil Change Light Chevrolet Impala, Monte Carlo, 2000-05
Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHG OIL SOON light flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio®. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to verify the exit.
How To Reset Oil Change Light Chevrolet Impala, Monte Carlo, 2000-05
Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHG OIL SOON light flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio®. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to verify the exit.
How To Reset Oil Change Light Chevrolet Impala, Monte Carlo, 2000-05
Turn the ignition to ON without starting the engine. Fully press and release the accelerator pedal three times within five seconds. If the CHG OIL SOON light flashes two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio®. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to verify the exit.
How To Reset Oil Change Light Chevrolet Camaro, 1998-02
To reset the OIL CHANGE light, press and hold the TRIP/OIL RESET button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset
How To Reset Oil Change Light Chevrolet Camaro, 1998-02
To reset the OIL CHANGE light, press and hold the TRIP/OIL RESET button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset
How To Reset Oil Change Light Chevrolet Camaro, 1998-02
To reset the OIL CHANGE light, press and hold the TRIP/OIL RESET button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset
How To Reset Oil Change Light Chevrolet Camaro, 1998-02
To reset the OIL CHANGE light, press and hold the TRIP/OIL RESET button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset
How To Reset Oil Change Light Chevrolet Camaro, 1998-02
To reset the OIL CHANGE light, press and hold the TRIP/OIL RESET button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset
How To Reset Oil Change Light Chevrolet Camaro, 1998-02
To reset the OIL CHANGE light, press and hold the TRIP/OIL RESET button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset
How To Reset Service Light For BMW
To reset the indicator:-
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
How To Reset Service Light For BMW
To reset the indicator:-
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
How To Reset Service Light For BMW
To reset the indicator:-
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
How To Reset Service Light For BMW
To reset the indicator:-
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
How To Reset Service Light For BMW
To reset the indicator:-
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
How To Reset Service Light For BMW
To reset the indicator:-
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
1.The car should be off-hold down the left instrument button (the trip odometer
reset)-while holding the key, turn the ignition to position 1 (radio)
2.You will see a test menu-keep holding the button-after maybe 10 seconds, the word "reset" will appear-let go of the button and press again-The indicator is reset!
How To Reset Service Light For Volvo S40 & V40
Reset Service Light Volvo S40, V40
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
How To Reset Service Light For Volvo S40 & V40
Reset Service Light Volvo S40, V40
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
How To Reset Service Light For Volvo S40 & V40
Reset Service Light Volvo S40, V40
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
How To Reset Service Light For Volvo S40 & V40
Reset Service Light Volvo S40, V40
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
How To Reset Service Light For Volvo S40 & V40
Reset Service Light Volvo S40, V40
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
How To Reset Service Light For Volvo S40 & V40
Reset Service Light Volvo S40, V40
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
S40 and V40 (1999+)
Hold down the odometer button
Turn the ignition so all the lights come on
Keep holding the odometer down for 30 secs or until the service light starts flashing
Release the odometer button while service light flashing
Turn off and on again to check
How To Program Subaru Outback Remote 2005
Programming new remotes The keyless entry system is equipped with a code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
How To Program Subaru Outback Remote 2005
Programming new remotes The keyless entry system is equipped with a code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
How To Program Subaru Outback Remote 2005
Programming new remotes The keyless entry system is equipped with a code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
How To Program Subaru Outback Remote 2005
Programming new remotes The keyless entry system is equipped with a code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
How To Program Subaru Outback Remote 2005
Programming new remotes The keyless entry system is equipped with a code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
How To Program Subaru Outback Remote 2005
Programming new remotes The keyless entry system is equipped with a code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
To register a new transmitter� with the keyless entry system, it is necessary to program the transmitter's code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the remote.� If there is no bag, open the remote and make a note� of the eight-digit number.
�the code is also inside the remote transmitter
Programming the remote transmitter code (from the owners manual) read through this first since eveything needs to be done in a quick sequence
1. Sit in the driver's seat, close all doors and the rear gate or trunk lid etc
2. Open and close the driver's door one time.
then� Within 45 seconds
3. open and close the driver's door once
4. turn the ignition key from LOCK to ON 10 times within 15 seconds. An electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered.
If you do not perform the steps above within 45 seconds an error will occur and neither an electronic tone� nor� the� buzzer� will� sound and the interior lamp will not flash. In this event, start all over again.
Within 45 seconds do the following Open and close the driver's door once within 15 seconds and an electronic tone will sound for 30 seconds. If� you do not perform the operations within 15 seconds an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with # 3 above.
Ok, here is the fun part...
Before the electronic tone stops, press the power door lock button to LOCK the same number of times as the leftmost digit of the transmitter code. For example, press the LOCK button 8 times if the leftmost digit of the code is 8. If the number is 3 then LOCK the door 3 times etc... When you have finished entering the number, push to UNLOCK side within five seconds and Then do that for all the remaining 7 digits of the code. After each series pull the lock knob to the UNLOCK side within five seconds.
When you are finished, within 5 seconds push that LOCK button to UNLOCK one time and then do it all again, the full series. Yes, once again start with the left digit and re-enter each one using the lock button within a few seconds. When you have entered the� eighth� digit the second time an electronic tone will sound for 30 seconds.
The electronic tone will stop sounding when you start entering the number. If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 above. If the interval between one push of the knob and the next exceeds five seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.
If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.
If you� wish to� program another transmitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning� with part 4. When you have finished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. Test to make sure it's right
How To Program Volkswagon Passat Remote
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
How To Program Volkswagon Passat Remote
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
How To Program Volkswagon Passat Remote
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
How To Program Volkswagon Passat Remote
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
How To Program Volkswagon Passat Remote
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
How To Program Volkswagon Passat Remote
1. Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
2. Mechanically lock vehicle at left front door, using second key.
3. On remote unit, press "Open" button once. A short horn signal will sound. Note: 􀂾 The "Open" button is pressed once for programming the first, or a single, remote unit. 􀂾 When programming additional remote units for the second, third or fourth memory addresses, press the "Open" button two, three or four times, in one-second intervals. 􀂾 Example: press the "Open" button once, wait 1 second, then press once again to program the second remote unit. 􀀹 After 6 seconds, press "Open" button once to activate the coding process.
4. The remote unit will now be coded, and it can be used to unlock the central locking system. Switch ignition off.
The key must be removed from the ignition before the remote unit can be used to lock the vehicle.The coding process can be repeated up to 4 times for additional remote units. In between each remote unit coding, the ignition must be switched off.
Memory addresses, erasing.
It is possible to erase the memory, e.g. if the customer has lost a remote unit. Proceed as follows.
ô€€¹ Switch ignition on with a key (don’t start the engine!); leave key in the ignition.
ô€€¹ Mechanically lock vehicle at left front door, using second key.
ô€€¹ On remote unit, press "Open" button 5 times in one-second intervals. A short horn signal will sound. ô€€¹ Then after 6 seconds, press "Open" button once to activate memory erasing process.
Memory is now erased, and the central locking system can no longer be operated by the remote unit. ô€€¹ Switch ignition off. As many as 4 new remote units can now be coded
How To Program Toyota Camry Remote
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
How To Program Toyota Camry Remote
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
How To Program Toyota Camry Remote
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
How To Program Toyota Camry Remote
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
How To Program Toyota Camry Remote
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
How To Program Toyota Camry Remote
1. Start with the key out of the ignition, drivers door is open all others closed and drivers door is unlocked.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
2. Perform these steps within 5 seconds. A. Insert the key into the ignition(Do NOT Turn) Pull key out. B. Insert the key into the ignition(Do NOT Turn) Pull key out.
3. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into the ignition(Do NOT Turn) Pull key out.
4. Perform these steps within 40 seconds. A. Close then open the drivers door. B. Close then open the drivers door. C. Insert the key into ignition and leave it in ignition. D. Close the drivers door. E. Turn the ignition to ON (Do NOT Start) then back to OFF. F. Remove the key from the ignition.
5. Within 3 seconds, the power door locks should lock then unlock automatically indicating successful entry into programming mode. Return to step 1 if the locks do not cycle at this point.
6. Perform these steps within 40 seconds. A. Press the lock and unlock buttons on the remtoe simutaneously for 1.5 seconds. B. Immediately after letting go of the lock and unlock buttons, Press the lock button by itself and hold for 2 seconds. Within 3 seconds, the door locks should lock and then unlock once indicating successful programming. If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted. C. Repeat steps A and B in step 6 for each new remote.
7. Open drivers door.
How To Program Lexus ES 300 Remote
1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
How To Program Lexus ES 300 Remote
1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
How To Program Lexus ES 300 Remote
1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
How To Program Lexus ES 300 Remote
1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
How To Program Lexus ES 300 Remote
1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
How To Program Lexus ES 300 Remote
1. Start with key out of ignition, drivers door is open all others closed and drivers door is unlocked.
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
2. Insert key into the ignition (Do NOT Turn) and Pull key out.
3. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Close, then open drivers door.
4. Perform these steps within 40 seconds. A. Using the power lock switch on the drivers door, perform 5 lock/unlock cycles starting with lock. Use an even pace and try to go about one cycle per second. (1Cycle = 1 lock and 1 unlock). B. Insert the key in the ignition cylinder. C. Turn the ignition to ON (Do NOT Start) then back to OFF. D. Remove the key from the ignition.
5. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors once.
6. Close and open drivers door.
7. Press any button on remote for a minimum of 1 second. System should now lock and unlock doors. Once to confirm programming, twice to indicate programming failed.
8. Repeat steps 5, 6 and 7 for additional remotes
How To Program Acura TL Remote 1997
Note: Entering the programming mode cancels all learned keyless remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode.
You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other
1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.)
3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2
6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode.
7. Within 10 seconds press the LOCK or UNLOCK button on same remote. 8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.
9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)
You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other
1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.)
3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2
6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode.
7. Within 10 seconds press the LOCK or UNLOCK button on same remote. 8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.
9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)
How To Program Acura TL Remote 1997
Note: Entering the programming mode cancels all learned keyless remotes, so none of the previously programmed remotes will work. You must reprogram all of the keyless remotes once you are in the programming mode.
You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other
1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.)
3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2
6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode.
7. Within 10 seconds press the LOCK or UNLOCK button on same remote. 8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.
9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)
You must complete each step within 4 seconds of the previous step to keep the system from exiting the programming mode. You must program remotes within 10 seconds of each other
1. Turn ignition switch to ON (II)
2. Within 4 seconds press the LOCK or UNOCK button on one of the remotes. (An unprogrammed remote can be used for this step.)
3. Within 4 seconds turn ignition switch to LOCK (0) position
4. Within 4 seconds turn the ignition switch to ON (II)
5. Repeat steps 2, 3 and 4 two more times using the same keyless remote used in step 2
6. Within 4 seconds press the LOCK or UNLOCK button on the same remote. Make sure the power door locks cycle to confirm you are in programming mode.
7. Within 10 seconds press the LOCK or UNLOCK button on same remote. 8. Within 10 seconds press the LOCK or UNLOCK button on all other remotes you want to program. Make sure door locks cycle after you push each remote button to confirm system has accepted the remote.
9. Turn the igniton switch to LOCK (0) to exit programming mode.
10. Test remote(s)
Subscribe to:
Posts (Atom)